<blockquote id="ad0y4" ></blockquote>

<blockquote id="ad0y4" ><meter id="ad0y4" ></meter></blockquote>

  • <source id="ad0y4" ></source>
  • <nobr id="ad0y4" ></nobr>

        <noscript id="ad0y4" ></noscript>
        <dl id="ad0y4" ><ins id="ad0y4" ><listing id="ad0y4" ></listing></ins></dl>

        <progress id="ad0y4" ><ol id="ad0y4" ></ol></progress>
      1. <dfn id="ad0y4" ></dfn>
          <optgroup id="ad0y4" ><dfn id="ad0y4" ><span id="ad0y4" ></span></dfn></optgroup>

          Contact us

          Mactron Technology.

          Tel: +86-769-2638 4404

          Fax: +86-769-2638 4091  

          Email: sales@   

                mactrontech@yahoo.com

          Skype: mactrontech

          Our New Site:

           

          Tel: +86-769-2638 4404
          Fax: +86-7

          Links

          CO2 Laser Power Source ( 80 watts )

          CO2 Laser Power Source ( 80 watts )

          80 watts Laser Power Source adopt high frequency design advantages, pay more attention to every component quality for major parts, and keep high performance and duration. 80 W laser power supplies were used to 70W – 80W CO2 laser tube for kinds of industrial laser system. Laser power supply produced by Mactron technology is well known with ultra long lifetime, stability, good compatibility, as first choice in 80W CO2 laser cutter and laser engraver.

           

          1. The main features of the 80W laser power supply:

           

          ◆Stable performance:

          Each power supply have been much more rigorous testing procedures, under full load high temperature (52~55 degrees celsius) 24 hours of aging, to ensure the stability of each power supply.

          ◆Good compatibility :

          Can adapt to a number of manufacturers 80W sealed off CO2 laser tube, but also has strong adaptability and fast response, engraving, cutting benefits good effect.

          ◆ Control is simple:

          Select high or low level control, the use of TTL-level control of the laser can start and stop. At the same time increase the protection switch, testing is through the external water and ventilation.

          Laser power control is simple, you can use 0 ~ 5V analog signal control the size of the laser power, you can also use the PWM (pulse width modulation) signal to be controlled.

          ◆Protection function:

          Power supply itself has open circuit protection, a good grounding in the case of protection, the power supply to short-term work in the open state, so to avoid the laser tube burst due to the damage caused by laser power supply, thereby enhancing the laser power supply of life.

          ◆Special Features: (optional addition)

          Power users do not need to open the shell, you can simply determine the laser power is working to distinguish between the failure of laser tube or power supply failure.

           

          1. 2. Specifications:

           

          Model

          Parameters

          80W Laser power

          Input

          Input Voltage

          AC220V±10% (Need AC110V products, ordering need indicate)

          AC frequency

          47 - 440HZ

          Cold-state Surge Current

          ≤60A(AC220V input)

          ≤30A(AC110V input)

          Leakage current

          ≤0.7mA(AC220V input) ≤0.4mA(AC110V input)

          Output

          Maximum output voltage

           

          DC40KV

          Maximum output current

          DC31mA(depending on the laser tubes of different manufacturers)

          Efficiency

          ≥90%( Full load)

          Response speed

          ≤ 1ms

           

          Control Interface

          TTL multilevel switching control, effective level can be high and low selection (see control wiring diagram)

          Insulation

          Input--output

          AC 1500V 1 minutes ≤10 mA

           

          Input--shell

          AC 1500V 1 minutes ≤10 mA

          Output--shell

          Connection

          Insulation Resistance

          ≥50MΩ(DC500V)

          Environmental
          Requested

           

          Working temperature

          -10℃ - 50℃

          Storage of temperature

           

          -20℃ - 75℃

          Relative Humidity

          Maximum 85% RH (non-condensing)

           

          Altitude

           

          100,000 feet of work 200,000 feet of storage, does not work

          Cooling methods

          Forced air cooling (fan cooling)

           

          Dimensions (L*W*H)

          285mm*190mm*95mm