<blockquote id="ad0y4" ></blockquote>

<blockquote id="ad0y4" ><meter id="ad0y4" ></meter></blockquote>

  • <source id="ad0y4" ></source>
  • <nobr id="ad0y4" ></nobr>

        <noscript id="ad0y4" ></noscript>
        <dl id="ad0y4" ><ins id="ad0y4" ><listing id="ad0y4" ></listing></ins></dl>

        <progress id="ad0y4" ><ol id="ad0y4" ></ol></progress>
      1. <dfn id="ad0y4" ></dfn>
          <optgroup id="ad0y4" ><dfn id="ad0y4" ><span id="ad0y4" ></span></dfn></optgroup>

          Contact us

          Mactron Technology.

          Tel: +86-769-2638 4404

          Fax: +86-769-2638 4091  

          Email: sales@   

                mactrontech@yahoo.com

          Skype: mactrontech

          Our New Site:

           

          Tel: +86-769-2638 4404
          Fax: +86-7

          Links

          Laser Controller MPC6535

          Laser Controller MPC6535

          Laser Controller MPC6535 improves major performance compared to MPC6515 Laser Control System in:
          (a). Better motion control around the corner;
          (b). Less interference thanks to the aluminum box.

          MPC6535 Laser Control Card is designed exclusively for the laser equipment. This high-performance Laser Controllers is based on the hardware solution of DSP+FPGA, is first choice for high quality Laser Cutting and Engraving System.

           

          1. Features:

          Stand-Alone motion controller
          Pulse frequency up to 7.5M Hz
          3-axis card for stepper motors or digital servo motors
          RS232 applicable for mainstream industrial touch-screen supporting Mudbug communication protocol
          Download data with USB flash disk or USB data cable
          Transfer speed with USB data cable up to 500Kb/s
          1-CH laser power on/off control output
          1-CH laser PWM control output
          Support 1or 2-CH independent power analog output
          PWM preheat control
          Uncapping protection
          Flying-optics compensation

           

          2. Packing List:

          Please check out the pack with below list. If there is something broken or lost, please contact you supplier instantly.


          No

          Part Name

          PCS

          Description

          Standard/Optional

          1

          MPC6535

          1

          Controller board with Aluminum case

          S

          2

          USB-AB-3M

          1

          Cable connected between PC and the MPC6535

          S

          3

          PAD03-E

          1

          Operation panel with English interface

          S

          4

          C4-PAD03-1.5M

          1

          Cable connected between PAD03 and the MPC6535

          S

          5

          U-disk

          1

          USB flash memory disk

          S

          6

          Dongle-white

          1

          LaserCut software key

          S

          7

          STD-01

          1

          Single converter module (single-ended to differential)

          O

          8

          PAD03-TR

          1

          Operation Panel with Turkish interface

          O

          9

          PAD03-C

          1

          Operation panel with Chinese interface

          O

           

          3. Quick Start:

          ● Run the setup.exe and follow the “next step” instruction to install LaserCut program into your computer.
          ● Install MPC6535 Laser Controller Board: mounting the board in the machine firmly. Must make the machine house wires with GROUND!

          4. Wiring Instruction:

          Must be careful with the positive and the negative end of 24VDC

          Connecting controller and drive
          Connecting Datum Switch
          Connecting Limit Switch
          Connecting laser power supply
          connecting other control ports

           

          5. Tune and Test:

          5.1 run the program, name Mpc05Ver+M05.exe to check the version.

          The firmware version should be as same as DLL version. If not, please update. For details, refer to LaseCut manual.
          5.2 Run Lasercut53.exe for Settings:

          1. Controller Type
          2. Laser Power
          3. Limit Datum Active Level
          4. Pulse Equivalency
          5. Working Table Size
          6. Homing Direction
          7. The Jerk is set as TEN times of the Acceleration
          8. The turn acceleration is set as TWO times of acceleration
          9. Tune for better performance

             (for details, go to see LaserCut manual)

          5.3 Download configure files and reset the laser control system
          5.4 Input working files, edit the diagram, make the settings, download the file into controller
          5.5 Start working.

           

          6. Others:
          1. Must be careful with the positive and negative ends of MPC6535’s power supply
          2. Must turn the power off when disconnect the cable between control PAD and the board.
          3. Make sure the metal case of MPC6535 wires to GROUND firmly
          4. Setting pulse mode in the parameter for controller signal receiving
          5. We recommend user take “LAS-”port for firing laser
          6. Make sure the Dongle Serial Number (SN) matches the board SN